Developing A Film

If you order your research paper from our custom writing service you will receive a perfectly written assignment on Developing A Film. What we need from you is to provide us with your detailed paper instructions for our experienced writers to follow all of your specific writing requirements. Specify your order details, state the exact number of pages required and our custom writing professionals will deliver the best quality Developing A Film paper right on time.

Out staff of freelance writers includes over 120 experts proficient in Developing A Film, therefore you can rest assured that your assignment will be handled by only top rated specialists. Order your Developing A Film paper at affordable prices with livepaperhelp.com!

Prepare developer, stop bath and fixer at 0°C


1. In total darkness, with 5mm film cut off the leader, snipping between perforations. Cut across the leading corners of the film at an angle, this makes it easier for the strip to slide into the reel. Load the film in the tank spirals. Put empty reel in as well at the top.


. Replace lid, turn on lights. Measure out developer in cylinder (0°C)


. Fill the tank with Film Developer in the cap (keep the tank at an angle) then tap it on flat surface to dislodge air bubbles. Start the timer at the same time (7 and half minutes time according to the film used see chart)


Custom Essays on Developing A Film


4. Immediately start agitation of the developer, agitate continuously but gently for 0 seconds and then place the tank on the worktop. Then wait 5 seconds and the agitate the tank (upside down) for 5 seconds, replace tank on worktop, wait another 5 seconds and so on until there is only 0 seconds remaining. Do not agitate in the final 0 seconds. (NOTE if it took you 15 seconds to fill the tank initially, begin to empty it 15 seconds before the time is up)


5. Between times prepare the stop bath. When there are 10 -0 seconds left of development time begin to pour away the developer at a rate so that the tank is empty at the finished dev. time


6. Set timer to 0 secs for stop bath and then add the Stop Bath and start the timer at same time, agitate for 0 seconds


7. Pour away the stop bath and set timer for fixer to 4 minutes, add the Fixer and agitate continuously but gently for 0 seconds and then place the tank on the worktop. Then wait 5 seconds and the agitate the tank (upside down) for 5 seconds, replace tank on worktop, wait another 5 seconds and so on until there is only 0 seconds remaining. Do not agitate in the final 0 secs.


8. Pour away the fixer and wash the film for about 0 minutes in running water (0°C) letting the water go into the tank


. After 0 minutes take the lid off (can keep light on), remove film from spirals and hang it up to dry (using clips). Leave the room, close the door and go back in several hours (1-) when the film is completely dry


Measurement of solutions for film development


All solutions should be stirred so that the temperature is 0 °C


Film Developer = 50ml


Water = 450ml


Adds up to 500ml


Stop Bath = 1fl.oz


Water = 1fl.oz


Adds up to 0fl.oz


Fixer = 100ml


Water = 00ml


Adds up to 400ml


Making A Print


Cut up 5mm film into strips of 6 frames and measure out solutions ready in the dishes


1. Turn off room light and turn on safe light and enlarger


. Place a negative in the enlarger carrier glossy side up (dull side down)


. Crank the enlarger up to the desired magnification


4. Focus the image of the negative on the print easel of the enlarger (a bit bigger the size of paper)


5. Stop down the lens by at least stops from the maximum f-5.6 or f-8


6. Turn off safelight and enlarger


7. Place paper in print easel, sensitive (shiny) side up


8. Set timer to 4 seconds and expose paper. Turn off enlarger and room lights


. Turn on safelight and set timer to 5 seconds and place exposed print in the print developer


10. 10 seconds before 5 seconds, using developing tongs lift the paper from developer wiping excess off


11. Place paper into the stop bath and return tongs to developer. Agitate the stop bath dish for 10 seconds, then using the fixer tongs, transfer the paper into the fixer dish and keep the solution in motion for about 40 seconds


1. The white light may be turned on. Take finished print out of the fixer and wash under water (0°C) for about minutes


1. Hang print up to dry using clips


To straighten print if become curled up, hold the print diagonally over the edge of a table. Grasp the protruding corner firmly and pull downward while holding the face of the print flat with the palm of the hand. Repeat this for each corner and the print should then have a reverse curl that will straighten.


Measurement of solutions for print development


All solutions should be made at a temperature of 0 °C. Can re-use solutions in dishes for up to 6-8hours.


Print Developer = 50ml


Water = 450ml


Adds up to 500ml


Stop Bath = 1fl.oz


Water = 1fl.oz


Adds up to 0fl.oz


Fixer = 100ml


Water = 00ml


Adds up to 400ml


Do this twice if not enough solution.


When you are finished processing for the day, just pour your fixer into a plastic jug that you have labelled as working fixer. This solution can be used over and over before it will become exhausted and will last about 6 months in a half-full stoppered bottle.





Please note that this sample paper on Developing A Film is for your review only. In order to eliminate any of the plagiarism issues, it is highly recommended that you do not use it for you own writing purposes. In case you experience difficulties with writing a well structured and accurately composed paper on Developing A Film, we are here to assist you. Your persuasive essay on Developing A Film will be written from scratch, so you do not have to worry about its originality.

Order your authentic assignment from livepaperhelp.com and you will be amazed at how easy it is to complete a quality custom paper within the shortest time possible!